Techcode® 2A KHz 20V PWM Buck DC/DC Converter Features. DATASHEET. TD General Description The TD is a KHz fixed frequency. TD datasheet, TD pdf, 2A KHZ 20V PWM Buck DC/DC Converter, Techcode, TD datasheet,Page, Techcode® 2A KHz 20V PWM Buck DC/DC Converter DATASHEET TD Function Description(Cont.) the inductor ripple.
|Published (Last):||8 August 2015|
|PDF File Size:||9.93 Mb|
|ePub File Size:||9.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
When the cycle by cycle current limit circuit is triggered, the output voltage drops as the duty cycle is decreasing. For the best thermal performance, wide td1410 datasheet traces and generous amounts of printed circuit board copper should be used in the board layout.
Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these spikes. It achieves 2A continuous output current over a wide input supply range with td1410 datasheet load and line regulation. To td1410 datasheet coupling to sensitive circuitry, the PC board copper area connected to this pin should be kept a minimum.
Power Switch Output Pin. Care must be taken in layout. A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents td1410 datasheet by the regulator.
Drive EN pin high to turn on the regulator, drive it low to. It achieves 2A continuous datasheett current over a wide input supply range with excellent load and line regulation. The data for these curves was taken with the TD SOP8 package operating as a buck-switching regulator in an ambient td1410 datasheet of 25oC still air.
Vendor Web Site 1 Diodes,Inc. These temperature rise numbers are td1410 datasheet approximate and there are many factors that can affect these temperatures. This pin should be placed outside of the Schottky Td1410 datasheet to output capacitor ground path to prevent switching current spikes from inducing voltage noise into TD In the TD buck regulator circuit, the two major power dissipating components are the TD and output inductor.
Td1410 datasheet inductor current stops rising. Typical Application Circuit 3.
Datasheet 2A KHZ 20V PWM Buck DC/DC
TD operates from a 3. The td1410 datasheet to ambient temperature can be td1410 datasheet from. An additional small LC filter can be added to the output as shown in Figure 14 to further reduce the amount of output ripple and transients. It achieves 2A continuous output current over a wide input supply range datsheet excellent load and line regulation. The first loop starts from.
Because of the unstable characteristics of ceramic capacitors made with Z5U material, they are not recommended. Allows the switching regulator circuit to be shutdown td1410 datasheet logic daatsheet signals thus dropping the total input supply current to approximately 30uA.
The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. The cycle by cycle current limit protection directly limits inductor peak current. When using the adjustable version, special care must datsaheet td1410 datasheet as to the location of the feedback resistors and the associated wiring.
Datasheet 2A 380KHZ 20V PWM Buck DC/DC
The second loop td1410 datasheet from the inductor, to the. The output rectifier diode supplies the current to the. The PWM control circuit is able to adjust the. Type and Reel Package P: Drive EN pin high to turn on the regulator, drive it low to turn it off. If open core inductors are used, special care must be taken as to td1410 datasheet location and positioning of this type of inductor. TD td1410 datasheet from a 3. A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by the regulator GND Circuit ground.
Stresses greater than those listed under Maximum Ratings may cause td1410 datasheet td410 to the device. Current flows in the second loop when the low td1410 datasheet diode is on. In PCB layout, minimizing the two loops area reduces the noise of this circuit and improves efficiency. Physically locate both resistors near the IC, and route the wiring away form the inductor especially an open core type of inductor.
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied. The first td1410 datasheet starts from the input capacitors, td1410 datasheet the VIN pin, to the VOUT pins, to the filter inductor, to the output capacitor and load, and then returns to the input capacitor through ground. The effectiveness of the PC board to dissipate heat also depends on the size, quantity and spacing of other components on the board, as well as whether the surrounding air is still or moving.
Bypass Vin to GND with a suitably large capacitorto eliminate noise on the td1410 datasheet.
EN is a digital input that turns the regulator td1410 datasheet or off. The TD serves as ideal power supply units for portable devices. Current flows in the first loop when the high side switch is. The TD serves as td1410 datasheet power supply units for portable devices. Supply Voltage Input Pin.