Find the most up-to-date version of ASTM D at Engineering ASTM D Lb9 LT5 m. D compaction are terms used interchangeably with preforming for PTFE. reground resin. Buy ASTM D Standard Specification for PTFE Molding and Molding and Extrusion Materials from SAI Global.

Author: Zolom Daisida
Country: Uruguay
Language: English (Spanish)
Genre: Education
Published (Last): 13 July 2004
Pages: 44
PDF File Size: 10.39 Mb
ePub File Size: 14.60 Mb
ISBN: 918-9-73921-625-2
Downloads: 2365
Price: Free* [*Free Regsitration Required]
Uploader: Yobar

For lower coefficient of friction applications, LUBRON TR slide bearing surfaces can be furnished with dimpled recesses to accommodate supplementary grease lubrication. Schedule This is a term for 1d457 internationally recognised range of nominal wall thicknesses for carbon steel and stainless steel pipes.

The PTFE bearing sliding surfaces shall be smooth and uniform in appearance, and shall show no evidence of any proturberance, delamination of other imperfections.

These materials astm d are astm d called fine powders are characterised by their consistent high performance, superior permeation resistance and excellent surface finish. Adtm follows the basic format of F Accreditation 1d such a standard is accomplished by a third party certifying authority that conducts routine v of any site wishing to hold and retain such astm d It is generally a compilation of the original liner specific standards and includes all the common lining materials plus several more unusual types.

The sole plate sliding surface shall be polished to a xstm 10 microinch 0.

Bearing design, AutoCAD drawing preparation, testing, consulting and on-site engineering services are available upon request. We would therefore recommend that any customer looking to write a general lined piping specification bases it upon the ASME standards. LUBRON TR slide bearings are bonded using high strength, heat-resistant, non-corroding, insoluble epoxy resin adhesives applied under factory controlled heat and pressure. This specification astm d widely used in the Grade B form as the standard pipe material for Lined Pipe and Fittings manufacture.

Interwoven with secondary glass fibers and bonded under pressure and temperature to carbon steel or stainless steel substrates, LUBRON TF bearings are capable of static loads up to 60, psi.


Much of this specification is astm d d with test methods for the materials as delivered by the polymer manufacturer and how the sintered material is to be tested by the wstm user. However, as the table below shows, very few of the standards actually give any values.

It has over the years been used as the bench mark quality standard astm d the manufacture of PTFE Lined pipe and fitting throughout most of the world with only astm d Europe preferring the DIN equivalent. It was written basically for two reasons, firstly to provide a specification for the many types of lined system within a common document and secondly to regularise the various differing techniques used by astm d major US manufacturers.

For elevated temperatures, the maximum allowable bearing pressure must be considered when sizing the slide bearing components. Type or Type with a mirror finish not exceeding 10 microinches 0. The best lining materials have high molecular weights and are astm d for their extraordinarily high viscosity even when they are fully melted.

Deformation Under Load — Total deformation after 24H. In trying to trace back the values seen across so many data sheets they are all in the same range, so we assumed they have some common sourcewe were able to find references old manuals released by DuPont, Dyneon and Daikin from where these values were obtained.

It has been mandatory throughout the EU since A type reference determines the mechanical and thermal astm d of Page 3 of 5 a particular grade or type. The qstm the melt flow index the greater the melt viscosity and performance in highly aggressive situations. Static Coefficient of friction.

Fluorinated Ethylene Propylene Copolymer (Melt Flow Index MI)

Welding of the slide bearing component asfm every direction of movement. Visit d157 at www. Much of this specification is taken up with test methods for d materials as delivered by the polymer manufacturer and how the sintered material is to be tested by the end user. The coefficient of friction generally decreases slightly with an increase in surface temperature.


Silicon grease conforming to Military Specification MIL-S is generally recommended for most structural applications. Load capacity will decrease with an increase in temperature.

There are some differences between this modern specification and the older series, these are mostly in the text and astm d of little significance in terms of performance. Slide bearings shall be designed to accommodate the total movement as specified.


This specification was originally written over 30 years ago sstm was made up from the best parts of the manufacturing methods of the v1457 US manufactures of that time. Upper and lower PTFE bearing components are capable of sliding movement unrestricted in any single plane direction. These materials are used for compression and Isostatic moulding and for Ram extrusion. ISO deals with the fundamentals of quality management systems, including the eight management principles on which the family of standards is based.

Corrosion resistance especially astmm to stress corrosion cracking at elevated temperatures is determined by the molecular weight and structure of the PFA. For cast-in-place concrete applications, LUBRON TR slide bearings can be supplied with anchor studs welded to the sliding surfaces must be maintained clean and free of aetm, grit and other contaminates which could effect the performance or service life of the bearing assembly.

Grade This reference defines the chemical composition and mechanical performance of the most ductile form of the two irons detailed in ASTM D4157 d This material has exceptionally good cold forming properties.

The lower the melt flow astm d the greater the melt viscosity and performance astm d highly aggressive situations.