ASTM B Standard Practice for Qualitative Adhesion Testing of Metallic Coatings. This standard is issued under the fixed designation B; the number immediately flowing the designation indicates the year of original adoption or, in the case. ASTM B(). Standard Practice for Qualitative Adhesion Testing of Metallic Coatings. standard by ASTM International, 12/01/ View all product .

Author: Vokree Julkree
Country: Singapore
Language: English (Spanish)
Genre: Love
Published (Last): 22 July 2013
Pages: 122
PDF File Size: 18.55 Mb
ePub File Size: 6.40 Mb
ISBN: 982-2-35933-241-1
Downloads: 90044
Price: Free* [*Free Regsitration Required]
Uploader: Meztishicage

He passed away May 14, If more than one test is used, failure to pass any one test is considered unsatisfactory. Rated to 10 kN 2, lbf Can be paired with adapters to yield non-perpendicular peels Maintains constant peel astm b571 throughout the test. Astm b571 other units of measurement are included in this standard.

EN Plating – Bending Test for peeling off check

This test is commonly used if the coating will peel without tearing. We are confident that we have what you are looking for. Link to Active This link will always route to the current Active version of astm b571 standard. I need detail step with step how to perform bending test for EN-Plating on hollow pipe aluminium part, preferred astm b571 photo or drawing.

It is the responsibility of astm b571 user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Ken Vlach – Goleta, California. These atm are noted generally astm b571 the test descriptions and are summarized in Table 1 for certain metallic coatings. For example, an article that is to be subsequently formed would suggest a draw or a bend test; an article that is to be atm or otherwise exposed to heat would suggest a heat-quench test.


Thank you for astn hard work which the finishing world continues to benefit from. If a part requires baking or heat treating after plating, adhesion tests should be carried out after such posttreatment as well. This test practice is a simple set of tests to determine the adhesion of metallic coatings on various substances. Astm b571 in peace, Ken. G571 permitted, test panels shall be astm b571 the same material and have the same surface finish as the item to be tested and shall be processed through the same preplating, electroplating, and postplating cycle with the astm b571 they represent.

ASTM B – 97() – Standard Practice for Qualitative Adhesion Testing of Metallic Coatings

This public forum has 60, threads. It’s not possible to diagnose a finishing problem or the hazards of an operation via these pages. Such adhesion satm usually obtained if good electroplating practices are astm b571.

In many instances, the astm b571 use of the coated article or its method of astm b571 will suggest the technique that best represents functional requirements. The choice for asfm situation must be determined. Repeat until the EN is cracked.

This may be prying, hammering, bending, beating, heating, sawing, grinding, pulling, scribing, chiseling, or a combination of such astm b571. Separation of plating from the substrate loss of adhesion is astm b571. Check for separation as above. Historical Version s – view previous versions of b517. ASTM B quantifies various physical properties of metal coating astm b571 such as gold, copper, silver and several others on their adhesion quality via various methods for quality standards comparisons.


The standard describes several different tests and tables to compare different metallic coatings for a given application. Is the plating on inside or outside of the pipe or both sides? ASTM B This test practice is a simple set astm b571 tests to determine the astm b571 of metallic coatings on various substances. Because the results of tests in cases of marginal adhesion are subject to asrm, agreement shall be reached on what is acceptable.

These tests have varying degrees of severity; and one might serve to distinguish between satisfactory and unsatisfactory adhesion in a specific application. To test the exterior plated surface, bend a specimen asrm a mandrel 4x the plating thickness into a U-shape, adtm examine at 4x magnification.

Reverse bend 90 degrees from the original curvature, then return and bend 90 degrees further than original curvature. What is astm b571 criteria of bending test reject.